Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome or via the app.
- Pop-up trimmer
- Trimmer release slide
- Shaving unit
- Shaving unit release button
- On/off button
- Menu button
- Socket for small plug
- Charging stand
- Supply unit
- Small plug
- Protection cap
- Pouch
- Philips Quick Clean Pod Cartridge
- Quick Clean Pod
- Cleaning brush
- Length settings
- Click-on beard styler attachment
- Comb for beard styler attachment
- Attachment holder
- Click-on cleansing brush attachment
Note: The accessories supplied may vary for different products. The box shows the accessories that have been supplied with your appliance.
| |
 | You can toggle through the menu items by pressing the menu button. |
| Icon | Meaning |
 | The main menu shows the status of the battery in percentages. |
 | The Motion Control sensor menu tells you if the motion during your shave was good or needs to be improved. |
 | The Pressure Guard sensor menu tells you if the pressure you applied to your skin during the shave was good, too low or too high. |
 | You can activate the travel lock in this menu. |
 | Here the display shows that your shaver is not paired to your smartphone. |
 | The display shows that your shaver is paired to your smartphone. |
| |
 | Press the on/off button to switch on the shaver. |
| Icon | Meaning |
 | When you switch on the shaver, a short animation shows which pressure feedback setting you activated. |
| |
| Icon | Meaning |
 | The battery is almost empty and you need to charge your shaver. |
 | When the data storage is almost full, you receive a notification reminding you to synchronize your shaves. To prevent data loss, synchronize the shaver with the app. |
  | The shaving unit is soiled or damaged to such an extent that the motor cannot run. Clean the shaving heads thoroughly. |
 | You are using the wrong supply unit. Only use the supply unit (HQ8505) that is supplied with the shaver. |
| |
| Icon | Meaning |
 | A reminder: clean your shaver in the quick cleaning pod. |
 | A reminder: clean your shaver. |
 | The cleaning process is in progress and the display shows the remaining cleaning time in seconds, or as a clock if you press the menu button. |
 | The cleaning process is interrupted. |
| |
| Icon | Meaning |
 | Unplug the shaver before you use it. |
Light ring feedback
During your shave, you receive feedback on how much pressure you are applying via the light ring at the top of your shaver handle.
The light ring on the handle lights up in various colors during your shave to give you feedback on how much pressure you are exerting. These are the default settings:
- When you don't apply enough pressure, the light ring lights up blue.
-
- When you apply the correct amount of pressure, the light ring lights up green.
-
- When you apply too much pressure, the light ring lights up orange.
When your shaver is switched on, you can customize the type of pressure feedback you receive.
- Switch on the shaver.
-
- Press the menu button to toggle through the pressure feedback options. The table below shows what pressure feedback you receive with each option.
| Too little pressure is being applied | The right amount of pressure is being applied | Too much pressure is being applied | |
| Full pressure feedback  | blue |  green |  orange |
| Partial pressure feedback  | No feedback | No feedback | orange |
| No pressure feedback  | No feedback | No feedback | No feedback |
Note: Note: Light ring feedback is only available when the shaving unit is attached to the handle.
When the beard styler or cleansing brush is attached to the handle, the motion and pressure feedback is switched off automatically.
When your shaver is switched off
Remaining battery charge
Motion Control sensor
Travel lock
Bluetooth
Note: This appliance is waterproof. It is suitable for use in the bath or shower and for cleaning under the tap. For safety reasons, the appliance can therefore only be used without cord.
- Charge the appliance before you use it for the first time and when the remaining battery charge indicates that the battery is almost empty.
- Charging takes approx. 1 hour.
- Quick charge: After approx. 5 minutes of charging, the battery contains enough energy for one full shave. When the battery is charged to 10 %, you can complete one full shave.
- When the appliance is fully charged it has a cordless operating time of up to 60 minutes.
- Note: You cannot use the appliance while it is charging.
Charging with the supply unit
- Make sure that the appliance is switched off.
-
- Insert the small plug into the appliance and put the supply unit in the wall socket.
- While the appliance is charging, an animation appears on the display showing the progress.
- When the appliance is fully charged, the battery percentage shows 100 % and the battery icon shows the battery being full.
- After charging, remove the supply unit from the wall socket and pull the small plug out of the appliance.
'Unplug for use' symbol
The 'unplug for use' symbol displays to remind you to disconnect the appliance from the wall socket and remove the small plug from the appliance before you switch it on.
Charging in the charging stand (specific models only)
- Make sure the appliance is switched off.
-
- Put the small plug in the charging stand and put the supply unit in the wall socket.
-
Place the appliance in the charging stand. Specific models only: The light ring on the bottom of the charging stand lights up and rotates quickly.
- After approximately 5 minutes, the light ring rotates slower. The battery now contains enough energy for one full shave.
- As the appliance continues to charge, the light ring becomes brighter and rotates slower.
- When the appliance is fully charged, the light ring lights up fully and stops rotating.
Warning: Always check the appliance and all accessories before use. Do not use the appliance or any accessory if it is damaged, as this may cause injury. Always replace a damaged part with one of the original type.
Shaving
You can use this appliance either wet or dry, or even in the shower. For a wet shave, apply some water and shaving foam or gel to your skin and rinse the shaving heads under the tap with warm water before following the steps below.
- Switch on the appliance.
-
- Move the shaving heads over your skin in circular movements (See 'Motion Control sensor' below) to catch all hairs growing in different directions. Make sure each shaving head is fully in contact with the skin. Exert gentle pressure for a close, comfortable shave.
- Note: Do not press too hard, as this can cause skin irritation. When you apply too much pressure, the orange light ring lights up.
-
- Note: If you are shaving with gel or foam, rinse the shaving unit regularly during your shave to ensure that it continues to glide smoothly over your skin.
-
- Use the narrow sides of the shaving unit to shave in hard-to-reach areas such as along your jawline and under your nose.
-
-
- Switch off and clean the appliance after each use.
- Note: Make sure you rinse all foam or shaving gel off the appliance.
When you are finished shaving and switch off your shaver you can also receive feedback about your overall shave on the handle. You can activate this feature via the app. Once you activate it you can toggle through the post-shave feedback by pressing the menu button.
Pressure Guard sensor
- When you apply the correct amount of pressure during your shave, the Pressure Guard sensor icon will display with a check mark.
-
- When your shaving pressure can be improved, the Pressure Guard sensor icon displays with an exclamation mark.
-
Motion Control sensor
- When you shave in the correct motion (circular movements), the Motion Control sensor icon displays with a check mark.
-
- When your shaving motion can be improved, the Motion control sensor icon displays with an exclamation mark.
If you want the post-shave feedback icons to be displayed directly after shaving, you can activate this feature via the app.
In the menu on your shaver, you can view the motion feedback from your last shave.
You can personalize your feedback settings, see more detailed feedback and get personalized advice via the app.
Skin adaptation period S7920 (app)
Cleaning reminder
When you switch off the appliance, the cleaning reminder is displayed to remind you to clean the appliance.
- Clean the appliance and attachments after each use to prevent clogging and damage.
- Clean the shaving heads thoroughly once a month or when the appliance does not shave as well as it used to.
Trimming
You can use the trimmer to groom your sideburns and moustache.
- Push the trimmer release slide downwards to open the trimmer.
- Switch on the appliance.
-
- Hold the trimmer perpendicular to the skin and move the appliance downwards while you exert gentle pressure.
-
- You can also use the trimmer under your nose.
- Switch off the appliance and clean the trimmer after each use to prevent clogging and damage.
- Close the trimmer.
Using the click-on attachments
Note: The accessories supplied may vary for different products. The box shows the accessories that have been supplied with your product.
Note: When the beard styler or cleansing brush is attached to the handle, the motion and pressure feedback is switched off automatically.
Using the beard styler attachment with comb
- Twist the shaving head or other attachment to remove it from the handle and press the beard styler attachment onto the handle.
-
- Slide the comb straight into the guiding grooves on both sides of the beard styler attachment.
-
- Press the length selector and then push it to the left or right to select the desired hair length setting.
- Switch on the appliance.
-
- Move the appliance upwards while you exert gentle pressure. Make sure the front of the comb is in full contact with the skin.
- Switch off the appliance and clean the attachment after use.
Using the beard styler attachment without comb
- Pull the comb off the beard styler attachment.
- Note: Grab the comb in the center to pull it off the beard styler attachment. Do not pull at the sides of the comb.
- Switch on the appliance.
-
- Hold the beard styler attachment perpendicular to the skin and move the appliance downwards while you exert gentle pressure.
- Switch off the appliance and clean the attachment after use.
Using the cleansing brush attachment
- Twist the shaving head or other attachment to remove it from the handle and press the cleansing brush attachment onto the handle.
- Moisten the cleansing brush with water.
- Do not use the cleansing brush dry as this can irritate the skin.
- Moisten your face with water and apply a cleanser to your face.
- Place the cleansing brush on your cheek.
- Switch on the appliance.
-
- Gently move the brush across your skin from the nose towards the ear. Do not press too hard. Make sure that the treatment remains comfortable.
- Do not cleanse the sensitive area around your eyes.
-
- After approx. 20 seconds, move the appliance to your other cheek and start cleansing this part of your face.
-
- After approx. 20 seconds, move the appliance to your forehead and start cleansing this part of your face. Gently move the brush head from left to right.
- We advise you to not overdo the cleansing and to not cleanse any zone longer than 20 seconds.
- Switch off the appliance and clean the attachment after use.
- After the treatment, rinse and dry your face. Your face is now ready for the next step of your daily skincare routine.
Storage
Note: We advise you to let the appliance and its attachments dry before you store them for the next use.
- Store the appliance in the pouch (if supplied).
- Put the protection cap (if supplied) on the shaver to protect it from dirt accumulation.
- Alternatively, store the appliance on the charging stand (if supplied) or in the Philips Quick Clean Pod (if supplied).
Clean the appliance and the attachments after each use for optimal performance.
How do I use the Quick Clean Pod?
What does the icon on my Quick Clean Pod mean?
| Icon | Behavior | Meaning |
 | Becomes visible on the Quick Clean Pod | The Quick Clean Pod Cartridge needs to be replaced. |
Preparing the Quick Clean Pod for use
- Twist and remove the top of the Quick Clean Pod.
-
- Twist the lid off of the Quick Clean Pod Cartridge.
-
- Lift the tab on the seal and pull it by the corner to remove the seal from the Quick Clean Pod Cartridge.
-
- Press the small circular piece on the handle of the Quick Clean Pod Cartridge to break the snap hook on the handle.
-
- Place the Quick Clean Pod Cartridge into the Quick Clean Pod.
-
- Put the top of the Quick Clean Pod back onto the base and turn it clockwise until you hear a click.
-
- Do not tilt the Quick Clean Pod to prevent leakage.
Using the Quick Clean Pod
- Place the shaver upside down into the Quick Clean Pod. The shaver automatically detects that it is in the Quick Clean Pod.
-
Switch on the shaver to start the cleaning program. Each cleaning program takes approximately one minute. During the cleaning program the remaining time is displayed as a countdown clock on the handle.
- Let the shaver air-dry completely in the Quick Clean Pod before storing it.
Replacing the Quick Clean Pod Cartridge
| Frequency of use | Cycles | When to replace the Quick Clean Pod Cartridge |
| Every day | About 30 | Every month |
| A few times per week | About 20 | Every 2 months |
| Every week | About 13 | Every 3 months |
| Every month | About 3 | Every 3 months |
- Twist and remove the top of the Quick Clean Pod.
-
- Lift the Quick Clean Pod Cartridge out of the Quick Clean Pod by the handle.
-
- Pour any remaining fluid down a drain and recycle the empty cartridge in accordance with local waste regulations.
-
-
Place a new Quick Clean Pod Cartridge into the Quick Clean Pod. Scan the QR code to the left or visit www.philips.com/cleaning-cartridge to order replacement Quick Clean Pod Cartridges.
Clean the shaver after each use to prevent clogging and damage.
Never dry the shaving unit with a towel or tissue, as this may damage the shaving heads.
While rinsing the shaving unit, water may drip out of the base of the shaver. This is a normal occurrence.
- Switch on the shaver.
- Rinse the shaving unit under a warm tap.
- Switch off the shaver. Press the release button to open the shaving unit.
- Rinse the hair chamber under a warm tap.
- Rinse the shaving head holder under a warm tap.
- Carefully shake off excess water and let the shaving head holder air-dry completely.
- Close the shaving unit.
We advise you to clean the shaving heads thoroughly once a month or when the shaver does not shave as well as it used to.
- Make sure that the appliance is switched off and disconnected from the wall socket.
- Press the release button on the shaving unit and pull the shaving head holder off the shaving unit.
- Rinse the hair chamber and shaving head holder under the tap.
- Remove the shaving heads. For detailed instructions, see 'How do I replace the shaving heads?'.
- Note: Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally put a cutter in the wrong shaving guard, it may take several weeks before optimal shaving performance is restored.
- Clean the cutter and guard under the tap.
- Shake off excess water.
- Put the shaving heads back into the shaving unit. For detailed instructions, see 'How do I replace the shaving heads?'.
- Insert the hinge of the shaving head holder into the slot in the top of the shaving unit and close the shaving unit.
Clean the trimmer after each use to prevent clogging and damage.
Caution: Never dry the trimmer teeth with a towel or tissue, as this may damage the trimmer teeth.
- Make sure that the appliance is switched off and disconnected from the wall socket.
- Push the trimmer release slide down to open the pop-up trimmer.
- Switch on the appliance and rinse the pop-up trimmer with warm water.
- After cleaning, switch off the appliance.
- Carefully shake off excess water and let the pop-up trimmer air dry.
- Close the trimmer.
- Tip: For optimal performance, lubricate the teeth of the pop-up trimmer with a drop of mineral oil every six months (oil not included).
Never dry the trimmer or beard styler attachments with a towel or tissue, as this may damage the trimming teeth.
The accessories supplied may vary for different products. The box shows the accessories that have been supplied with your product.
Cleaning the cleansing brush attachment
Clean the cleansing brush attachment after each use.
- Switch off the appliance.
-
- Remove the attachment from the attachment holder.
- Clean the parts thoroughly with warm water and soap.
- Dry the attachment with a towel.
Cleaning the beard styler attachment
Clean the beard styler attachment after each use.
- Pull the comb off the beard styler attachment.
- Note: Grab the comb in the center to pull it off the beard styler attachment. Do not pull at the sides of the comb.
-
- Rinse the cut hairs off the cutting unit with lukewarm water.
- Rinse the cut hairs off the comb.
-
- Remove the cutting unit from the beard styler attachment. By pushing the cutting unit from the beard styler attachment you can remove any hairs that have accumulated inside the beard styler. You can also rinse the back of the cutting unit.
-
- Rinse cut hairs out of the beard styler attachment.
- Carefully shake off excess water and leave the comb, cutting unit and beard styler attachment to air-dry before next use.
- Never dry the cutting unit with a towel or tissue, as this may damage the trimming teeth.
-
- When the cutting unit is dry attach it to the beard styler attachment.
-
- When the comb is dry, re-attach it to the beard styler.
- Tip: For optimal performance, lubricate the teeth of the beard styler attachment with a drop of sewing machine oil regularly.
Benefits of connecting your shaver to the app
You can use the app for a variety of personalization and coaching options such as:
- Real-time motion and pressure feedback and guidance
- Synchronizing your shave data and tracking your shave history
- Improving your shave routine and reducing shaving-related skin issue
- Recommendations on style
- Customization of post-shave feedback
- Personalized advice
Pair the shaver and smartphone
The app is compatible with a wide range of iPhone and Android™ smartphones.
More information is available at www.philips.com/MyShaver9000-app
- Download the app.
-
- Make sure Bluetooth on your smartphone is switched on.
-
- Switch on the shaver to activate Bluetooth.
- Open the app and follow the instructions to start the pairing process.
-
- Once paired, the shaver and app connect automatically when the app is open and Bluetooth on your phone is switched on.
Synchronise your shaves
This shaver stores your shave data so you don't need to take your smartphone with you when you shave or want to check your shave data at a later stage.
When the data storage is almost full, you receive a notification reminding you to synchronize your shaves. To prevent data loss, synchronize the shaver with the app.
- Make sure your phone is close to the shaver and open the app.
- The app connects automatically and synchronizes your last shaves.
Unpair the shaver and smartphone S7000R2
You can pair your shaver with only one smartphone at a time. To unpair your shaver from your smartphone (e.g. when you get a new smartphone), follow these steps:
- First, unpair your shaver.
-
- Toggle through the menu items by pressing the menu button until you reach the Bluetooth menu.
-
- Press and hold the menu button until you are presented with a cross and check mark selection.
-
- Select the check mark by pressing the menu button again to unpair your shaver.
Note: When your shaver is successfully unpaired, you see the Bluetooth icon on your shaver handle shown to the left.
Note: When you want to pair your shaver and smartphone again, make sure that both are unpaired first.
- Then, unpair your smartphone.
- Go to the settings on your smartphone and select Bluetooth.
- Tap on the name of the shaver.
- Tap 'forget' or 'unpair'.
- Note: The unpairing procedure may vary by smartphone. Please check your smartphone manual for more information.
For maximum shaving performance, we advise you to replace the shaving heads every two years.
Replace damaged shaving heads immediately. Always replace the shaving heads with original Philips shaving heads.
Replacing the shaving heads
- Switch off the shaver.
-
- Press the release button on the shaving unit and pull the shaving head holder off the shaving unit.
-
- Turn the retaining rings anticlockwise and remove them. Place them aside in a safe place.
-
-
Remove the shaving heads from the shaving head holder. Discard the used shaving heads immediately to avoid mixing them with the new shaving heads.
-
- Place new shaving heads in the holder.
-
- Place the retaining rings back onto the shaving heads and turn them clockwise to reattach the retaining rings.
-
- Each retaining ring has two recesses that fit exactly into the projections of the shaving head holder. Turn the ring clockwise until your hear a click to indicate that the ring is fixed.
-
- Insert the hinge of the shaving head holder into the slot in the top of the shaving unit and close the shaving unit.
To buy accessories or spare parts, visit www.philips.com/parts-and-accessories or go to your Philips dealer. You can also contact the Philips Consumer Care Center in your country (see the international warranty leaflet for contact details).
The following accessories and spare parts are available:
- SH91 Philips shaving heads
- CC12 Cleaning cartridge 2-pack
- CC13 Cleaning cartridge 3-pack
- CC16 Cleaning cartridge 6-pack
Note: The availability of the accessories may differ by country.
This chapter summarizes the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, visit www.philips.com/support for a list of frequently asked questions or contact the Consumer Care Center in your country.
Shaver
| I cannot connect the shaver. | You have not downloaded the app. | Download the app. |
| Your shaver and smartphone are not paired yet. | Pair your shaver and smartphone following the instructions in the app. | |
| The first pairing attempt failed. | Unpair your shaver and smartphone and try pairing them again. | |
| Your smartphone cannot find your shaver. | Make sure your smartphone is equipped with Bluetooth 4.2 or higher. | |
| Make sure Bluetooth is activated on your smartphone and that the travel lock is switched off on your shaver. | ||
| Make sure that your smartphone is within one meter of your shaver to enable a Bluetooth connection. | ||
| Make sure your shaver is charged. | ||
| Your shaver and smartphone were once paired. You only unpaired the shaver. | Go to the Bluetooth settings on your smartphone. Make sure your smartphone is also unpaired. Then try pairing them again. | |
| I want to use the shaver without the app. | You do not have to connect your shaver to your smartphone before each shave. The shaver works fine without the app, although you will not experience the same benefits. To get personalized shaving tips, just make sure that you connect it at least once every 20 shaves to synchronize your shave data. | |
| The appliance does not work when I press the on/off button. | The appliance is still attached to the wall socket. For safety reasons, the appliance can only be used without cord. | Unplug the appliance and press the on/off button to switch on the appliance. |
| The rechargeable battery is empty. | Recharge the battery. | |
| The travel lock is activated. | Press the menu button for 3 seconds to deactivate the travel lock. | |
| The shaving unit is soiled or damaged to such an extent that the motor cannot run. | Clean the shaving heads thoroughly or replace them. | |
| The appliance does not shave as well as it used to. | The shaving heads are damaged or worn. | Replace the shaving heads. |
| Hairs or dirt obstruct the shaving heads. | Clean the shaving heads thoroughly. | |
| Water is leaking from the bottom of the appliance. | During cleaning, water may collect between the inner body and the outer shell of the appliance. | This is normal and not dangerous because all electronics are enclosed in a sealed power unit inside the appliance. |
Philips Quick Clean Pod
| Problem | Possible cause | Solution |
| My shaver isn't clean after using the Philips Quick Clean Pod. | You removed the shaver before the cleaning program was finished. | Leave the shaver in the Philips Quick Clean Pod for the full cleaning program. Each cleaning program takes approximately 1 minute. The cleaning icon goes out when the cleaning program is finished. |
| The Philips Quick Clean Pod Cartridge needs to be replaced. | Replace the Philips Quick Clean Pod Cartridge. | |
| The Philips Quick Clean Pod is tilted. | Place the Philips Quick Clean Pod on a flat surface. | |
| My Philips Quick Clean Pod does not switch on. | The Philips Quick Clean Pod is powered by the motor of the shaver. | Place the shaver into the Philips Quick Clean Pod. Switch on the shaver. |
| The shaver is connected to the wall socket. | Disconnect the shaver from the supply unit. | |
| The shaver battery is empty. | Charge the shaver before using the Philips Quick Clean Pod. | |
| My Philips Quick Clean Pod is overflowing. | You regularly use the Philips Quick Clean Pod after rinsing the shaver but not shaking off excess water. | Shake off excess water after rinsing the shaving heads each time before putting the shaver into the Philips Quick Clean Pod. |
| You shaved with shaving gel or foam and did not rinse the shaver before using the Philips Quick Clean Pod. | Rinse the shaving heads thoroughly before using the Philips Quick Clean Pod. |
